Makers of MOSES - The Final Answer in Marine Simulation
Rev. 7.05 Bug Fixes
REV NO: REV 7.05.001

DATE: November 04, 2010 Discovered By: Lars Rune Helland

Description Of Problem

The relative velocities reported with ST_CLEARENCE are wrong.

REV NO: REV 7.05.002

DATE: November 05, 2010 Discovered By: Lars Rune Helland

Description Of Problem

The previous fix was not quite right.

REV NO: REV 7.05.003

DATE: November 09, 2010 Discovered By: Lars Rune Helland

Description Of Problem

Sometimes a vertical tube can contribute a waterplane area even if it is totally submerged.

REV NO: REV 7.05.004

DATE: November 17, 2010 Discovered By: Georgina Maldonado

Description Of Problem

The description for "magnitude" on the CONFORCE command always X**2 + Y**2 + Z**2.

REV NO: REV 7.05.005

DATE: November 22, 2010 Discovered By: Greg Hook

Description Of Problem

Sometimes the NT_FATIGUE value for BEAM_POST does not get all the fatigue points it should.

REV NO: REV 7.05.006

DATE: November 23, 2010 Discovered By: Georgina Maldonado

Description Of Problem

If one does &INFO(severity warn) it will not work correctly.

REV NO: REV 7.05.007

DATE: November 29, 2010 Discovered By: Georgina Maldonado

Description Of Problem

"TEE" shapes and deleted degrees of freedom from SACS are not correctly converted.

REV NO: REV 7.05.008

DATE: December 07, 2010 Discovered By: Rene Perez

Description Of Problem

The computation of Qf for the second supplement of RP2A 21st edition is not quite correct.

REV NO: REV 7.05.009

DATE: December 07, 2010 Discovered By: Rene Perez

Description Of Problem

The Joint code check report does not properly report the chord forces.

REV NO: REV 7.05.010

DATE: December 14, 2010 Discovered By: Georgina Maldonado

Description Of Problem

RARM -STOP was not honoring the option selection.

REV NO: REV 7.05.011

DATE: December 16, 2010 Discovered By: Georgina Maldonado

Description Of Problem

     &describe body xxx -IGNORE
does not "not ignore" all degrees of freedom.
REV NO: REV 7.05.012

DATE: January 13, 2011 Discovered By: Greg Hook

Description Of Problem

If a model has a beam with 21 fatigue points, the you will get a fatal error "Output Line Too Long".

REV NO: REV 7.05.013

DATE: January 14, 2011 Discovered By: Greg Hook

Description Of Problem

If one has a number defined with a "long string" then the number will be evaluated with a truncated string and no error will be given.

REV NO: REV 7.05.014

DATE: January 19, 2011 Discovered By: Lars Rune Helland

Description Of Problem

The propeller efficiency on a prop connector does not work correctly for negative velocities.

REV NO: REV 7.05.015

DATE: January 29, 2011 Discovered By: Lars Rune Helland

Description Of Problem

A control system cannot control a PROP connector.

REV NO: REV 7.05.016

DATE: February 15, 2011 Discovered By: Lars Rune Helland

Description Of Problem

If one has multiple inmodels the wrong "curv" may be associated with a winch.

REV NO: REV 7.05.017

DATE: February 16, 2011 Discovered By: Greg Hook

Description Of Problem

The -EULER -X option does not quite work correctly.

REV NO: REV 7.05.018

DATE: February 17, 2011 Discovered By: Georgina Maldonado

Description Of Problem

The second end of a GSPR, LMU, or FOUNDATION connector is not reported correctly in the &STATUS G_CONNECTOR report if the connector has a non zero length.

REV NO: REV 7.05.019

DATE: March 09, 2011 Discovered By: Herm Bussemaker

Description Of Problem

The report one receives after a resize is not correct if one has non prismatic members.

REV NO: REV 7.05.020

DATE: March 10, 2011 Discovered By: Herm Bussemaker

Description Of Problem

Resize of classes with multiple segments sometimes does not work.

REV NO: REV 7.05.021

DATE: March 16, 2011 Discovered By: Wei Wang

Description Of Problem

Sometimes the -DENSITY option will be incorrectly omitted if the density specified is "too close" (.2%) to the default value.

REV NO: REV 7.05.022

DATE: March 17, 2011 Discovered By: Tim Nolte

Description Of Problem

The coefficient defined with -DRGPLA is only used for current drag, but not for wind.

REV NO: REV 7.05.023

DATE: March 30, 2011 Discovered By: Herm Bussemaker

Description Of Problem

The RANGE command in the Disposition Menu is broken.

REV NO: REV 7.05.024

DATE: March 30, 2011 Discovered By: Georgina Maldonado

Description Of Problem

The -DOWN_FLOOD option for compartment flooding was broken.

REV NO: REV 7.05.025

DATE: March 31, 2011 Discovered By: Greg Hook

Description Of Problem

A the discovery "butt weld" at a node (not a tubular joint) changes the SCF but not the SN.

REV NO: REV 7.05.026

DATE: April 13, 2011 Discovered By: Yvan Leipold

Description Of Problem

The AREA card from SACS is not converted correctly.

REV NO: REV 7.05.027

DATE: May 19, 2011 Discovered By: R. Nachlinger

Description Of Problem

In some cases, slam cdrs are not computed correctly.

REV NO: REV 7.05.028

DATE: June 22, 2011 Discovered By: Georgina Maldonado

Description Of Problem

Sensor settings are not updated when &EQUI is performed.

REV NO: REV 7.05.029

DATE: July 08, 2011 Discovered By: Georgina Maldonado

Description Of Problem

The &INFO(VALUE_SENSOR) returns the result in computational units, not report units.

REV NO: REV 7.05.030

DATE: July 22, 2011 Discovered By: Greg Hook

Description Of Problem

There are inconsistencies between the documentation and the program for the "PROPULSION" class. This changes the program to conform to the documentation.

REV NO: REV 7.05.031

DATE: August 22, 2011 Discovered By: R. Nachlinger

Description Of Problem

One may not have enough space allocates when doing RAOS for a large number of frequencies and headings and with connectors.

REV NO: REV 7.05.032

DATE: August 22, 2011 Discovered By: R. Nachlinger

Description Of Problem

The number of bodies selected for BODY_FORCE is not initialized.

REV NO: REV 7.05.033

DATE: August 26, 2011 Discovered By: R.Nachlinger

Description Of Problem

Sometimes one would get a SEGMENT VIOLATION on a Mac when doing a stress analysis.

REV NO: REV 7.05.034

DATE: September 26, 2011 Discovered By: Greg Hook

Description Of Problem

Sometimes if one has both clump weights and spring buoys then &STATUS D_GEOM may not converge.

REV NO: REV 7.05.035

DATE: September 27, 2011 Discovered By: Georgina Maldonado

Description Of Problem

For some strange systems on may receive a message "Could Not Find Catenary Solution".

REV NO: REV 7.05.036

DATE: October 03, 2011 Discovered By: Yvan Leipold

Description Of Problem

An error message about offsets on a launch leg was not being issued when it should.

REV NO: REV 7.05.037

DATE: October 21, 2011 Discovered By: Herm Bussemaker

Description Of Problem

If all connectors are inactive, one will be shown in a picture.

REV NO: REV 7.05.038

DATE: October 25, 2011 Discovered By: Roy Koo

Description Of Problem

If one plots a picture of a system including a winch, he may get an extra line.

REV NO: REV 7.05.039

DATE: November 04, 2011 Discovered By: Ray Nachlinger

Description Of Problem

If one uses BEAM_POST CODE -B_LOAD YES -DETAIL the report will be wrong

REV NO: REV 7.05.040

DATE: November 16, 2011 Discovered By: Herm Bussemaker

Description Of Problem

Plotting of connector force RAOs for more than one heading is broken.

REV NO: REV 7.05.041

DATE: December 12, 2011 Discovered By: Devi Presad

Description Of Problem

The roll and pitch angles reported in the TANK_CAPACITY report are wrong.

REV NO: REV 7.05.042

DATE: December 19, 2011 Discovered By: John Windus

Description Of Problem

It you have a complicated mooring system and a control system, it may not work.

REV NO: REV 7.05.043

DATE: December 21, 2011 Discovered By: Greg Hook

Description Of Problem

It there are no downflooding points, MOSES sets the height to zero and this messes up some stability checks. This fix sets the height for a null set of points to 9999.

REV NO: REV 7.05.044

DATE: December 22, 2011 Discovered By: Greg Hook

Description Of Problem

Yesterday's fix was not quite correct.

REV NO: REV 7.05.045

DATE: January 05, 2012 Discovered By: Yvan Leipold

Description Of Problem

Running Simple Joint Fatigue will give segmentation fault if you have more than one load case.

REV NO: REV 7.05.046

DATE: January 19, 2012 Discovered By: Herm Bussemaker

Description Of Problem

Using tip-hook assemblies with GDOFs does not work.

REV NO: REV 7.05.047

DATE: January 19, 2012 Discovered By: Herm Bussemaker

Description Of Problem

The previous fix was not correct.

REV NO: REV 7.05.048

DATE: January 20, 2012 Discovered By: Herm Bussemaker

Description Of Problem

Previous fix was still not quite right.

REV NO: REV 7.05.049

DATE: January 23, 2012 Discovered By: Ray Nachlinger

Description Of Problem

Sometimes strange things happen when using a tip-hook assembly.

REV NO: REV 7.05.050

DATE: February 07, 2012 Discovered By: Greg Hook

Description Of Problem

SACS WGTNS cards are not properly converted.

REV NO: REV 7.05.051

DATE: February 14, 2012 Discovered By: Yvan Leipold

Description Of Problem

On some Linux systems the MOSES window would not appear or would only briefly flash on screen.

REV NO: REV 7.05.052

DATE: February 15, 2012 Discovered By: Kelvin Frazer

Description Of Problem

Using -L_DYNAMIC CURVE +VEL LIM does not correctly set the upper line length limit.

REV NO: REV 7.05.053

DATE: February 29, 2012 Discovered By: Harrison Yu

Description Of Problem

The allowable shear stress reported in the beam code check results is incorrect.

REV NO: REV 7.05.054

DATE: March 15, 2012 Discovered By: R. Nachlinger

Description Of Problem

Sometimes a connector will not be correct when making a picture.

REV NO: REV 7.05.055

DATE: March 15, 2012 Discovered By: Georgina Maldonado

Description Of Problem

Class name for ring segment was getting redefined.

REV NO: REV 7.05.056

DATE: April 23, 2012 Discovered By: Peter Lai

Description Of Problem

The damping matrix one gets with MATRICES command in the Frequency Response Menu is incorrect if one has more than one body.

REV NO: REV 7.05.057

DATE: April 24, 2012 Discovered By: Peter Lai

Description Of Problem

The fix 7.05.056 was not correct.

REV NO: REV 7.05.058

DATE: April 27, 2012 Discovered By: Andy Zhu

Description Of Problem

Using ED_ELEM to change the releases on a beam will result in no change.

REV NO: REV 7.05.059

DATE: July 06, 2012 Discovered By: R.Nachlinger

Description Of Problem

The motion of the drift force is not properly added to the right hand side for SRESPONSE.