REV NO: REV 502.001
| DATE: August 26, 1995 | Discovered By: R. Nachlinger |
Description Of Problem
If one has a syntax error in either an RAO or SRESPONSE command, the program will abort with "FREQ_MARK Already Allocated".
Programs Affected: All
REV NO: REV 502.002
| DATE: August 26, 1995 | Discovered By: Georgina Maldonado |
Description Of Problem
If one has more than one body, then the added mass and damping matrices in the FREQ_RESPONSE Menu will not be correct.
Programs Affected: MOSES, OSCAR II
REV NO: REV 502.003
| DATE: September 01, 1995 | Discovered By: Roger Burger |
Description Of Problem
One cannot use PI -PLANE until after some PI has been issues.
Programs Affected: All
REV NO: REV 502.004
| DATE: September 06, 1995 | Discovered By: Carl Webb |
Description Of Problem
The -SLOSH option disappears when an &CMP_BAL command is used. Also, the resulting ballast condition may not be in equilibrium when -SLOSH is re-established.
Programs Affected: All
REV NO: REV 502.005
| DATE: September 13, 1995 | Discovered By: R. Nachlinger |
Description Of Problem
If one selects -CG on a TRAJ command, then the title will say "location of the origin" instead of "location of the cg".
Programs Affected: all
REV NO: REV 502.006
| DATE: September 13, 1995 | Discovered By: R. Nachlinger |
Description Of Problem
The flow rate is incorrect when there is an internal pressure.
Programs Affected: All
REV NO: REV 502.007
| DATE: September 14, 1995 | Discovered By: R. Nachlinger |
Description Of Problem
If one floods a tube tank (&compartment -flood), the buoyancy force will not be correct.
Programs Affected: All
REV NO: REV 502.008
| DATE: September 20, 1995 | Discovered By: Carl Webb |
Description Of Problem
In very rare circumstances, one can get a bad plot of a mooring line. This occurs primarily when one has a lot of segments and verify low pretensions.
Programs Affected: All
REV NO: REV 502.009
| DATE: September 22, 1995 | Discovered By: R. Nachlinger |
Description Of Problem
For some problems when a body is far away from the global origin, &weight -compute may not yield a good answer.
Programs Affected: All
REV NO: REV 502.010
| DATE: September 26, 1995 | Discovered By: Bill Greiner |
Description Of Problem
The Fourier Coefficients reported with EXFORCE for
following a SRESPONSE are incorrect by a factor of 12.
Programs Affected: All
REV NO: REV 502.011
| DATE: September 27, 1995 | Discovered By: C. Owens |
Description Of Problem
Offsets on plates do not work correctly.
Programs Affected: MOSES
REV NO: REV 502.012
| DATE: October 10, 1995 | Discovered By: |
Description Of Problem
The string function &BODY was not returning the proper value for the body center of gravity.
Programs Affected:
REV NO: REV 502.013
| DATE: October 23, 1995 | Discovered By: Roger Burger |
Description Of Problem
The results of &body( weight ) are incorrect if one has defined a load group margin.
Programs Affected: All
REV NO: REV 502.014
| DATE: October 23, 1995 | Discovered By: Roger Burger |
Description Of Problem
The command v_tanaka does not produce results which can be plotted. The report, however, is correct.
Programs Affected: All
REV NO: REV 502.015
| DATE: October 23, 1995 | Discovered By: Guillume Le Marechal |
Description Of Problem
If one has a compartment with the same name as a part, but not the current part, then the load mapping will not be correct.
Programs Affected: OSCAR II, MOSES
REV NO: REV 502.016
| DATE: October 24, 1995 | Discovered By: Peter Lai |
Description Of Problem
If one has a body z axis which is radically different from vertical, then Morrison's' equation in the frequency domain will not be correct.
Programs Affected: All
REV NO: REV 502.017
| DATE: October 24, 1995 | Discovered By: Curtis Owens |
Description Of Problem
If plates elements are quite small, then their bending stiffness is too large.
Programs Affected: MOSES
REV NO: REV 502.018
| DATE: October 25, 1995 | Discovered By: Roger Burger |
Description Of Problem
If one resizes, and no mating shapes are found in the table, then some machines may abort with a Fortran write error.
Programs Affected: MOSES
REV NO: REV 502.019
| DATE: October 28, 1995 | Discovered By: R. Nachlinger |
Description Of Problem
If one has over 200 input tokens, problems will result, even though there is no error message.
Programs Affected: All
REV NO: REV 502.020
| DATE: October 30, 1995 | Discovered By: Yvan Leipold |
Description Of Problem
If one imports a hydrodynamic database during an inmodel, and then attempts to read hydrostatic data, an error will result.
Programs Affected: All
REV NO: REV 502.021
| DATE: November 01, 1995 | Discovered By: R.Nachlinger |
Description Of Problem
The velocity and acceleration statistics computed in the FREQ_RESP menu are incorrect when derived from a SRESPONSE.
Programs Affected: All
REV NO: REV 502.022
| DATE: November 03, 1995 | Discovered By: R. Nachlinger |
Description Of Problem
The spectral linearization for viscous damping of Morrison's equation elements is not quite correct.
Programs Affected: All
REV NO: REV 502.023
| DATE: November 07, 1995 | Discovered By: R. Nachlinger |
Description Of Problem
If one adds data to #tanker for TBEAM or AEY, they will be incorrectly scaled and give bad wind forces.
Programs Affected: All
REV NO: REV 502.024
| DATE: December 06, 1995 | Discovered By: Tim Nolte |
Description Of Problem
The tolerance for a vertical tube is too coarse. This causes a tube at small roll angles to have an incorrect cb.
Programs Affected: All
REV NO: REV 502.025
| DATE: December 13, 1995 | Discovered By: Curtis Owens |
Description Of Problem
When "cans" are used to support a jacket during transportation using the install macros, it is likely that the can will be chosen as the chord. This messes up the offsets, and the joint classification.
Programs Affected: MOSES
REV NO: REV 502.026
| DATE: December 22, 1995 | Discovered By: Georgina Maldonado |
Description Of Problem
In &instate command issued within the Hydrostatics Menu has no effect.
Programs Affected: all
REV NO: REV 502.027
| DATE: December 29, 1995 | Discovered By: R. Nachlinger |
Description Of Problem
Sometimes a transportation does not find equilibrium.
Programs Affected: All
REV NO: REV 502.028
| DATE: February 05, 1996 | Discovered By: R. Nachlinger |
Description Of Problem
One cannot use a rod element to model a buoy connected to a production riser.
Programs Affected: MOSES, OSCAR II
REV NO: REV 502.029
| DATE: February 07, 1996 | Discovered By: Sturle Hegreness |
Description Of Problem
Plots and tensioning of lines with attachments below the anchors does not work properly.
Programs Affected: All
REV NO: REV 502.030
| DATE: February 21, 1996 | Discovered By: V. Bouyssy |
Description Of Problem
The command &describe nod_nas will give an incorrect error message. Everything still works as documented.
Programs Affected: All
REV NO: REV 502.031
| DATE: February 24, 1996 | Discovered By: Anders Nedreberg |
Description Of Problem
There are difficulties with ALINEs with bottom slope and small pretension.
Programs Affected: All
REV NO: REV 502.032
| DATE: March 05, 1996 | Discovered By: J. Jorgensen |
Description Of Problem
A PC will abort with a co-processor fault if one trys to do diffraction on a mesh with a line as a panel.
Programs Affected: All
REV NO: REV 502.033
| DATE: March 07, 1996 | Discovered By: G. Marechal |
Description Of Problem
The drift forces are incorrect during a SRESPONSE if the body has greatly changed heading.
Programs Affected: All